Flsun v400

Flsun v400

The Flsun v400 is a delta printer controlled by the speederpad. It was purchased on the 1st March 23 as part of the policy on the hackspace policy of providing "better" machines than people have access for at home. The printer enables fast printing, enabling large complex prints to be completed under 24 hours.

The project was funded from the sale of donated v1.2 Raspberry PIs to the hacker community!

The v400 is being modified with an enclosure, fire puck to allow unattended printing and HEPA/Active Carbon filter for indoor ASA/ABS printing. Please do not print in ASA/ABS or leave unattended until the enclosure project is complete.

Its maximum off the shelf print speed is 400mm/s, though whilst it will almost always reach this speed, it performs best on simple models with long sections.

It has a maximum print diameter of 300mm and can print upto 410mm. Be aware delta printers perform poorly at the max height range and there is a coning effect which means it's not a complete cylinder at the highest point.

Induction is mandatory for this printer, not because it is not simple to use, but because customisations must be made to your printer profile to enable the modified fans to purge the print area when using known cancer causing materials to keep you and other space members safe. If you are using the PC in the print lab and are not changing settings, this is the simpliest option!

For complex prints, it is recommended to reduce the stock speed acceleration to 6000mm/s and the max print speed to 350mm/s. This usually only increases long complex print speeds by a matter of minutes. Anything with simple designs will be fine at this speed.

Maintainers

• Tim Neobard
• Steve Tong

Please note, we only support Cura 5.x - if you want to use a different slicer, we cannot offer support. Sorry! Though you're welcome to become a maintainer who does...

Printing ASA or ABS

ASA or ABS printing requires a higher surface temperature, but this risks the curie point of the magnetic bed.

• Ensure you have completed the induction and your CURA profile (or similar) includes the correct settings for the HEPA Filter to enable safe printing.
• Please do not attempt to print higher than 95'C
• Do not remove the magnetic bed until it has cooled completely.
• Do not leave ASA or ABS in the printer, please replace with a standard reel of PLA and purge the nozzle once your print is complete.

Please report any damage to the magnetic bed to discord.

PID tuning

The printer is PID tuned to 210'c print head and 60'c bed. This is the standard PLA print settings which are the most used settings by the hackspace.

If you are struggling with ASA/ABS we may need to retune to 295'c and 95'c however please try without first as it involves editing the firmware of the printer which is beyond the scope of this wiki page at present.

Autolevelling

Autolevelling requires the installation of the autolevelling probe.

This is not something that needs to be done routinely as the bed is not adjustable, however if you are getting poor adhesion with standard PLA, then you may need to rerun this.

Please note, when the bed needs to be autolevelled, it means the Z offset may also be incorrect. Setting the Z offset incorrectly could damage the printer. Damage to the magnetic bed is expensive, so if you have any doubts let us know. The following procedure should be done by those who are competent to do so.

Autolevelling procedure:

• Message the 3D print discord that you are running this process (We may need to double check the settings)
• Heat the bed to 60'C (Temperature > Heater bed > set temp > type 60, press tick)
• Allow to "soak" for 5-10 minutes. (Allow to come to temp, THEN go make a cup of tea)
• Goto configuration > bed level > bed mesh
• Attach the autolevelling sensor to the print head (it is magnetic)
• Attach the sensor lead into the white port at the top of the printer
• Click continue on speeder pad
• Allow the machine to run the auto level procedure
• Detatch the autolevelling sensor from the top of the printer very carefully!
• Remove the sensor from the bottom of the print head (it is magnetic)

Whilst the bed is hot, you will most likely also need to update the Z offset.

• Place a piece of thin paper on the print bed.
• Goto configuration > bed level > move Z0
• Adjust the head so that the paper is slightly gripping.
• Press top left back button when it is at the correct height.

Check your next print, if it is not adhering, you may need to adjust the head slightly further down (use the 0.05 measurement until you are happy)

v400 Community

For additional profiles & advice you can join the v400 community below:

https://www.facebook.com/groups/flsunv400/

Cura Profile 5.x Install Instructions

Download the following file:

https://drive.google.com/file/d/11JbcBx69SSi3piii1x1SFIQIUNgIOFHv/view?usp=share_link

Extract and follow the following instructions

1. Place the "flsun_v400 folder" in the "share\cura\resources\quality" directory under the cura5.x installation path.

2. Place the "flsun_v400.def.json" file to "share\cura\resources\definitions" directory in the installation path.

3. Place the "flsun_v400_extruder_0.def.json" file in the "share\cura\resources\extruders" directory in the installation path.

4. Place the "flsun_v400. stl" file under the "share\cura\resources\meshes" directory in the installation path.

5. Close all open CURA software and add V400 after opening it again.

Speeder pad firmware

The speeder pad runs FLSun forked firmware. Please do not "upgrade" this to official Klipper as this will require more changes in the slicer settings related to reading stored autolevelling mesh.